• a component of an electricity system which divides an electrical power feed into subsidiary circuits, while providing a protective fuse or circuit breaker each circuit, in a common enclosure, a main switch, and in recent boards, one or more Residual current devices(RCD) or Residual current breakers with overcurrent protection (RCBO), will also be incorporated.

Distribution boards are sometimes known as:

• breaker panels
• fusebox
• fuseboard
• circuit breaker panel
• consumer unit or CU
• panelboard
• load centre (center in North America)
• power breaker

The circuit breakers are generally placed in two columns. Circuit breaker panelboards are always dead front, that is, the operator of the circuit breakers cannot contact live electrical parts. During servicing of the distribution board itself, though, when the cover has been removed and the cables are visible, North American breaker panelboards commonly have some live parts exposed.

Breaker arrangement

Each row is fed from a different phase (A, B and C below), to allow 2- or 3-pole common-trip breakers to have one pole on each phase. In North America it is common to wire large permanently-installed equipment line-to-line. This takes two slots in the panel (two-pole) and gives a voltage of 240V if the supply system is SPLIT PHASE and 208 V if the supply system is THREE-PHASE.

UK Boards

In the UK, domestic and small commercial or public installations usually have single-phase supplies at 230V (nominal standard). The main distribution boards in these installations are technically referred to as consumer units (CUs), though informally they may be known as fuse boxes; older consumer units used fuses until the advent of Mini Circuit Breakers (MCBs).

A consumer unit normally has a single horizontal row of fuses or MCBs, though some older units grouped four fuses in a “square” arrangement. For two-rate supplies (standard/off-peak), a second CU may be added (“stacked”). Multiple CUs, which may or may not be in close proximity, are also found in larger premises.

Larger commercial, public, and industrial installations generally use three-phase supplies, with distribution boards which have twin vertical rows of breakers. Larger installations will often use subsidiary distribution boards.

In both cases, modern boards handling supplies up to around 100A (CUs) or 200A (distribution boards) are usually based on on DIN rail mountings and use circuit breakers (rather than fuses) and RCDs. The main distribution board in an installation will also normally provide a main switch (known as an “incomer”) which switches the phase and neutral lines for the whole supply. (n.b. an incomer may be referred to – or sold as – an “isolator”, but this is problematic, as it will not necessarily be used as an isolator in the strict sense.)

For each phase, power is fed along a busbar; in “split” panels, separate busbars are fed directly from the incomer, which allows RCDs to be used to protect groups of circuits. Alternatively RCBOs may be used to provide both overcurrent and residual-current protection to single circuits.

Other devices, such as transformers (e.g. for bell circuits) and contactors (relays – e.g. for large motor or heating loads) may also be used.

New British distribution boards generally have the live parts enclosed to IP20, even when the cover has been removed for servicing.

Modern CU

A typical new domestic CU used as a main panel may have anything from 6 to 24 ways for devices (some of which may occupy two ways), and will be split into two or more sections (e.g. a non-RCD section for alarms etc., an RCD-protected section for socket outlets, and an RCD-protected section for lighting and other built-in appliances). Secondary CUs used for outbuildings usually have 1 to 4 ways plus an RCD.

Older CUs

Recent (pre-17th edition wiring regulations) CUs would not usually have RCD protected sections for anything other than socket outlets, though some older CUs used RCD Incomers. Before the 1990s RCDs (and split busbars) were not standard in CUs.

Rewirable Fuse Boxes

1950s MEM rewirable fuse box (covered)	1950s MEM rewirable fuse box (open)
1970s MEM rewirable fuse box (covered)	1970s MEM rewirable fuse box (open)

Fuse Boxes usually use cartridge or rewirable fuses with no other protective device, and basic 4 ways boxes are very common. Some older boxes are made of brown-black bakelite, sometimes with a wooden base. Although their design is historic, these were standard equipment for new installs as recently as the 1980s, so are very common.

Users should be wary of these fuseboxes, as typically pulling a fuse carrier out with the power on results in fingers grasping live connections, and these boxes are widespread even in modern installations.

The popular 4-way fusebox usually has 2 lighting and 2 socket circuits, with heavy or sustained loads such as immersion heater and oven on a socket circuit. This arrangement is not recommended practice today, but it is common in existing installations. Larger boxes with more ways will have separate fuses for large loads such as immersion heater, oven and shower.

MCB Retrofits

Some of these fuseboxes have had their fuse carriers relaced with plug-in MCBs. These retrofit MCBs are typically rated at 3kA breaking capacity, but many homes or properties have PSCCs as high as 6kA. Hence these MCBs do not have sufficient breaking capacity for safe reliable operation in many premises.

Historic Fuseboxes

A small number of pre-1950 fuseboxes are still in service. These should be treated with caution because exposed live parts are common on these boxes. The installations they supply will not meet modern standards for electrical safety. Another characteristic of very old installations is that there may be two fuses for each circuit – one on the live and one on the neutral. In rare instances, old ring circuits may be encountered with no less than 4 15A fuses per ring, one on each of L and N, and this duplicated for each of the 2 feeds for the ring.

Inside a UK distribution board

This picture shows the interior of a typical 12-position UK distribution panel. The three incoming phase wires connect to the busbars via a main switch in the centre of the panel. On each side of the panel are two busbars, for neutral and earth. The incoming neutral connects to the lower busbar on the right side of the panel, which is in turn connected to the neutral busbar at the top left. The incoming earth wire connects to the lower busbar on the left side of the panel, which is in turn connected to the earth busbar at the top right. The cover has been removed from the lower-right neutral bar; the neutral bar on the left side has its cover in place.

Down the left side of the phase busbars are two two-pole RCBOs and two single-pole breakers, one unused. Down the right side of the busbars are a single-pole breaker, a two-pole RCBO and a three-pole breaker.

The two-pole RCBOs in the picture are not connected across two phases, but have supply-side neutral connections exiting behind the phase busbars.

The illustrated panel includes a great deal of unused space; it is likely that the manufacturer produces 18- and 24-position versions of this panel using the same chassis.

In a UK-style board, breaker positions are numbered top to bottom in the left hand column, then top to bottom in the right column. Each number is used to label one position on each phase, as below, and can be seen faintly in the photograph to the right. It remains to be seen how the WIRING recently introduced in the UK will affect this labelling.

For reasons of aesthetics and security, circuit breaker panels are often placed in out-of-the-way closets, attics, garages, or basements, but sometimes they are also featured as part of the aesthetic elements of a building (as an art installation, for example) or where they can be easily accessed. However, current US building codes prohibit installing a panel in a bathroom (or similar room), in closets intended for clothing, or where there is insufficient space for a worker to access it. Specific situations, such as an installation outdoors, in a hazardous environment, or in other out-of-the-ordinary locations may require specialized equipment and more stringent installation practices.

Large buildings or facilities with higher electric power demand may have multiple circuit breaker panels. In this case, the panels are often indicated by letters of the alphabet. One case is The Decon Gallery, a modern building in downtown Toronto, which has 11 breaker panels designated "A", "B", "C", "D", and so on. A backstage outlet is therefore labeled "C27". In many such buildings, each outlet is on its own circuit breaker, and the outlets are labelled in the above specified manner to facilitate easy location of which breaker to shut off for servicing, rewiring, or the like.

In even larger buildings, such as schools, hospitals and sports/entertainment venues it is not uncommon to have scores of panels, specially designated for each building depending on how the architects and electrical engineers subdivide the building. They are commonly designated as either 3-phase or 1-phase normal power or emergency power. In these set-ups they may also be designated for their use, such as distribution panels for supplying other panels, lighting panels for lights, power panels for equipment and receptacles and special uses for whatever type of building they are used in. It is also not uncommon for these panels to be located throughout the building in electric closets serving a section of the building.

In a theatre a specialty panel called a dimmer is used to feed stage lighting instruments. A US style dimmer rack has a 208Y/120 volt 3 phase feed. Instead of just circuit breakers, the rack has a solid state electronic dimmer with its own circuit breaker for each stage circuit. This is known as a dimmer-per-circuit arrangement. The dimmers are equally divided across the three incoming phases. In a 96 dimmer rack, there are 32 dimmers on phase A, 32 dimmers on phase B, and 32 on phase C to spread out the lighting load as equally as possible. In addition to the power feed from the supply transformer in the building, a control cable from the lighting desk carries information to the dimmers in a control protocol . The information includes commands on levels, fade times, and which dimmers come up and go out during the lighting changes of the show (light cues).

Distribution boards may be surface-mounted on a wall or may be sunk into the wall. The former arrangement allows for easier alteration or addition to wiring at a later date, but the latter arrangement may look neater, particularly in a residential situation. The other problem with recessing a distribution board into a wall is that if the wall is solid a lot of brick or block may need to be removed - for this reason recessed boards are generally only fitted on new-build projects when the required space can be built into the wall.

Mobile operation

Sometimes it is desired to have a portable breaker panel, for example, for special events. In this case, a breaker panel is mounted to a board, together with various sockets. These are common in the movie industry. The American one pictured at the right has a cord with plug to supply power. Power leaves the board through four three-phase circuits: three 15 A; and one 20 A circuit. The 15 A circuits each go to a triple box. The 20 A circuit goes to an L21-20 receptacle, and one leg of it goes to a 20 A duplex receptacle shown at the upper left. The neon nightlights on the upper right triplex box are to show the phase presence.